Ara
Toplam kayıt 29, listelenen: 11-20
Development and characterization of clinoptilolite-, mordenite-, and analcime-based geopolymers: A comparative study
(Elsevier, 2021)
This study examines the development of geopolymers from clinoptilolite, mordenite, and anal-cime and compares the properties of the resulting green-binding materials. Sodium silicate and sodium hydroxide solutions were ...
Effect of characteristics of natural zeolites on their geopolymerization
(Elsevier, 2021)
The properties of clinoptilolite-based geopolymers are investigated with a focus on the parameters affecting the reactivity of clinoptilolite in a geopolymer binder. A complete characterization of raw materials was carried ...
Effect of arc re-melting on microstructure, mechanical and tribological properties of commercial 390A alloy
(Elsevier, 2021)
To investigate the effect of the arc re-melting on the microstructure, mechanical and tribological properties of the 390A alloy, its ingot produced by the conventional induction melting method was subjected to the arc ...
Sodium silicate effect on setting properties, strength behavior and microstructure of cemented coal fly ash backfill
(Elsevier, 2021)
Representing an engineered mixture of coal fly ash, cement and water, cemented coal fly ash backfill (CCB) is typically employed for filling the openings created after coal excavation in the earth. A high rate of productivity ...
Effect of zinc content and cutting tool coating on the machinability of the Al-(5-35) Zn alloys
(Korean Inst Metals Materials, 2020)
In this study, Al-5Zn, Al-15Zn, Al-25Zn and Al-35Zn alloys containing 5, 15, 25 and 35 wt% Zn, respectively were produced by permanent mold casting. Their microstructures and mechanical properties were investigated using ...
Effect of different zinc contents on the structural, mechanical and tribological properties of EN AC-48100 (Al-17Si-4Cu-Mg) Alloy
(Gazi Univ, Fac Engineering Architecture, 2020)
In this study, Al-17Si-4Cu-0.6Mg-0.2Ti which is based of the EN AC-48100 alloy, Al-17Si-4Cu-0.6Mg0.2Ti-1Zn, Al-17Si-4Cu-0.6Mg-0.2Ti-2Zn, Al- 17Si-4Cu-0.6Mg-0.2Ti-3Zn, Al-17Si-4Cu-0.6Mg-0.2Ti-4Zn and Al-17Si-4Cu-0.6Mg-0.2Ti-5Zn ...
Processing of T6 heat-treated Al-12Si-0.6Mg alloy
(Taylor & Francis Inc, 2020)
In this study, ternary Al-12Si-0.6Mg material was manufactured by gravity die casting method in induction melting furnace. Microstructure images of alloy were taken on optical microscope after T6 heat treatment. Hardness, ...
Effect of content and length of polypropylene fibers on strength and microstructure of cementitious tailings-waste rock fill
(MDPI, 2023)
The mechanical strength properties of cemented tailings backfill are very important for the safe and environmentally friendly mining of mineral resources. To check the impact of polypropylene fiber on strength and ...
Cementitious backfill with partial replacement of Cu-rich mine tailings by sand: rheological, mechanical and microstructural properties
(MDPI, 2023)
The thinning of tailings gradation during ore processing leads to a sizeable fall in the strength of cementitious paste backfill (CPB), increases operational risks, and encourages researchers to use alternative economic ...
Effect of strontium on the microstructure, mechanical, and tribological properties of the Zn-40Al-2Cu alloy
(Springer, 2023)
Zn-40Al-2Cu and Zn-40Al-2Cu-0.1Sr alloys were produced by permanent mold casting method. The microstructure, mechanical properties and wear resistance of the produced alloys were investigated. Microstructural examinations ...