Erişim şekli için "info:eu-repo/semantics/openAccess" Mühendislik Fakültesi listeleme
Toplam kayıt 248, listelenen: 141-160
-
Investigation of clean energy production in drinking water networks
(Springer, 2024)Viable renewable energy sources must be low-cost, easy to install, clean, and reliable if they are to meet the energy demand of urban or rural areas. Water is able to provide efficient sources of electrical energy among ... -
Investigation of GSM, LTE and Wi-Fi electromagnetic radiation in dwellings
(Polish Acad Sciences Inst Physics, 2017)Electromagnetic radiation exposure increases with the rise of the wireless communication devices. Electromagnetic radiation, especially near 2400 MHz band, has gradually increased with the widespread of wireless fidelity ... -
Investigation of nano ulexite mineral effects on mechanical behaviour of warm mix asphalt pavements
(Croatian Soc Civil Engineers-Hsgi, 2020)The research presented in the paper shows that further investigations on additives used in the warm mix asphalt technology are needed. It was observed that the negative effect of adhesion loss in asphalt mixes produced by ... -
Investigation of passive radar target detection performance improvement by using multiple co-located FM radio transmitters
(2019)Interest in passive radar systems is increasing because of its hidden operational capabilities, cost effectiveness and low maintenance requirements. The greatest advantage of these systems is that they can detect and follow ... -
Investigation of photocatalytic performance of GaN-WSSe under vertical strain
(Recep Tayyip Erdoğan University, 2023)The utilization of mechanical strain is an essential way to modify and optimize the physical properties of materials, possibly making them usable for a variety of applications, including nanoelectronics and renewable ... -
Investigation of the cutting forces and surface roughness in milling carbon fiber reinforced polymer composite material
(Inst Za Kovinske Materiale I in Tehnologie, 2016)In this study, milling of a carbon-fiber-reinforced polymer composite material (CFRP) was investigated experimentally using various carbide end mills. the input parameters included the spindle speed, feed rate and cutting ... -
Investigation of the effect of different power degree NdFeB magnets used in interior permanent magnet brushless direct current motor (IPMBLDC) on motor performance
(Gazi Üniversitesi, 2023)Purpose: In this study, it is aimed to determine the effects of magnets used in BLDC motors on the motor performance of NdFeB type magnets with different power densities at different temperatures. Theory and Methods: The ... -
Investigation of the effects of T5 and T6 heat treatments on the structural, mechanical, and tribological properties of Zn-40Al-2Cu-0.1Sr alloy
(Gazi Üniversitesi, 2024)To assess the effects of T5 and T6 heat treatments on the structural, mechanical, and tribological properties of Zn-40Al-2Cu-0.1Sr alloy several ingots were produced by the permanent mold casting. The structure and properties ... -
İnsan ve koyun femur kemiğinin mekanik özelliklerinin sonlu elemanlar yöntemiyle karşılaştırılması
(2021)İnsan ve hayvan sağlığı araştırmalarında sonlu elemanlar yöntemi (SEY) kullanılarak gerçekleştirilen analiz çalışmaları, bilgisayar teknolojisinin de gelişmesiyle birlikte önem kazanmıştır. SEY analiz çalışmaları fare, ... -
A joint experiment and discussion for strength characteristics of cemented paste backfill considering curing conditions
(MDPI, 2022)As lots of underground mines have been exploited in the past decades, many stope instability and surface subsidence problems are appeared in the underground mines, while the cemented paste backfill (CPB) technology has ... -
Kararlı durumda seri kapasitörlerin iletim şebekesine etkilerinin incelenmesi
(2019)Artan nüfus ve gelişen sanayi ile birlikte elektrik enerjisi ihtiyacı günden güne artmaktadır. Bu talebin karşılanması için yeni üretim tesisleri birincil enerji kaynaklarına yakın yerlerde kurulmakta ve iletim şebekesi ... -
Kokil kalıba döküm yöntemi ile üretilmiş Al-12Si-(0,02-1)Sr alaşımlarının CVD-TiCN/Al2O3/TiN kaplamalı kesici uç ile tornada işlenmesinde kesme kuvveti ve yüzey pürüzlülüğü üzerine deneysel çalışma
(Gazi Üniversitesi , Fen Bilimleri Enstitüsü, 2022)In this study, three Al-12Si-Sr alloys containing different ratios (0.02; 0.1 and 1%) strontium (Sr) were manufactured by the permanent mold casting method. The microstructures of the manufactured alloys were determined ... -
A large goaf group treatment by means of Mine Backfill Technology
(Hindawi, 2021)There are few studies on the management methods of large-scale goaf groups per the specific surrounding rock mass conditions of each goaf. This paper evaluates comprehensively the stability of the multistage large-scale ... -
Learner characteristics and competencies
(Springer, 2023)The advances in technology and the demand for open, distance, and digital education redefined the characteristics and competencies of learners in these learning environments. Although technology ownership and access to an ... -
Low-cost multimode diode-pumped Tm:YAG and Tm:LuAG lasers
(2019)We report a continuous-wave operation of Tm:YAG and Tm:LuAG lasers pumped with a low-cost, multimode AlGaAs laser diode. First, the lifetime and the absorbance behavior of 5 mm, 6% Tm3+ -doped YAG and LuAG crystals were ... -
Machine learning based feature optimization and early detection system in heart diseases
(IEEE, 2023)In today's world, humanity faces a myriad of challenges, many of which pose significant threats to our well-being. Chief among these challenges are health-related issues. Among these health problems, heart diseases stand ... -
Mechanical and radiation attenuation properties of conventional and heavy concrete with diverse aggregate and water/cement ratios
(Croatian Association of Civil Engineers, 2022)This paper presents the results of comprehensive laboratory work conducted for investigating the mechanical and radiation attenuation characteristics of heavyweight concrete produced with pyrite, chromium, and magnetite ... -
A method to classify steel plate faults based on ensemble learning
(2022)With the industrial revolution 4.0, machine learning methods are widely used in all aspects of manufacturing to perform quality prediction, fault diagnosis, or maintenance. In the steel industry, it is important to ... -
Micro-Sized glucose biosensor based on composite pH sensor
(2018)Today's scientific and technical advances have led to significant advances in biosensor technology, leading to widespread use of biosensors in areas such as food technology, the environment, pharmaceuticals and clinical ... -
Modification of tea biochar with Mg, Fe, Mn and Al salts for efficient sorption of PO43- and Cd2+ from aqueous solutions
(Iwa Publishing, 2019)There is a requirement to provide more efficient, sensitive, low-cost materials for remediation of contaminated water. Biochar as a sorbent is an effective and low-cost material to remove contaminants in water but its ...