Dil "eng" Mühendislik Fakültesi için listeleme
Toplam kayıt 786, listelenen: 321-340
-
Fabrication of gold thin films on cooled glass substrates
(Springer, 2024)In this article, gold (Au) thin films were fabricated on glass substrates under vacuum conditions (4.5 x 10(-6) Torr) within a temperature range of 100-300 K, incrementing in steps of 50 K. Analyses through Field Emission ... -
Fast pyrolysis of tea bush, walnut shell, and pine cone mixture: Effect of pyrolysis parameters on pyrolysis crop yields
(MDPI, 2023)Liquid products obtained by the fast pyrolysis process applied to biomass can be used as chemical raw materials and liquid fuels. In this study, tea bush, walnut shell, and pine cone samples selected as biomass samples ... -
Fault and sensor error diagnostic strategies for a vapor compression refrigeration system by using fuzzy inference systems and artificial neural network
(Elsevier Sci Ltd, 2015)A fuzzy inference system (FIS) and an artificial neural network (ANN) were used for diagnosis of the faults of a vapor compression refrigeration experimental setup. A separate EIS was developed for detection of sensor ... -
Fault diagnosis of a vapor compression refrigeration system with hermetic reciprocating compressor based on p-h diagram
(Elsevier Sci Ltd, 2014)The aim of this study is to show how to use the p-h diagram successfully for diagnosing faults in the vapor compression refrigeration cycle. This new approach is able to remove the gap between the information required to ... -
Fiber length effect on strength properties of polypropylene fiber reinforced cemented tailings backfill specimens with different sizes
(Elsevier Sci Ltd, 2020)The strength properties of cemented tailings backfill (CTB: an engineered mix of processing tailings, hydraulic binder and mixing water) is strongly affected by its structural integrity. However, our understanding of the ... -
Finite element analysis of ratcheting on beam under bending-bending loading conditions
(Techno-Press, 2024)Ratcheting is the cyclic buildup of inelastic strain on a structure resulting from a combination of primary and secondary cyclic stress. It can lead to excessive plastic deformation, incremental collapse, or fatigue. ... -
Finite element analysis of the behavior of elliptical cracks emanating from the orthopedic cement interface in total hip prostheses
(Techno-Press, 2024)This study examines crack behavior within orthopedic cement utilized in total hip replacements through the finite element method. Its main goal is to compute stress intensity factors (SIF) near the crack tip. The analysis ... -
Finite element analysis of the femur fracture for a different total hip prosthesis (Charnley, Osteal, and Thompson)
(Techno-Press, 2023)Total hip replacement is a crucial intervention for patients with fractured hips who face challenges in natural recovery. The design of durable prostheses requires a comprehensive understanding of the natural processes ... -
Finite element analysis of the mechanical behavior of the different angle hip femoral stem
(Techno-Press, 2022)Femoral stems with proximal metaphyseal involvement are commonly used total hip replacement components with very good results. In this study, total hip arthroplasty (THA) application was analyzed using a three-dimensionally ... -
Finite element modeling of contact between an elastic layer and two elastic quarter planes
(Techno-Press, 2020)In this study, a two dimensional model of receding contact problem has been analyzed using finite element method (FEM) based software ANSYS and ABAQUS. For this aim finite element modeling of elastic layer and two homogeneous, ... -
Fire retardation, compressive strength and durability analysis of concrete reinforced with novel plasters: An experimental, computational and statistical research
(Elsevier, 2024)Concrete is an essential component of the construction industry, valued for its high compressive strength (CS) and durability. However, when exposed to extreme conditions like fire without protective structural elements, ... -
A flexible PV-powered battery-charging scheme for electric vehicles
(Taylor & Francis Ltd, 2017)This paper presents a new design for a low-impact, fully controlled, and flexible self-adjusting DC side pulse-width modulation (PWM)-hybrid modulated filter compensation (HMFC) scheme for multi photovoltaic-arrays utilized ... -
Floating PVs in Terms of Power Generation, Environmental Aspects, Market Potential, and Challenges
(MDPI, 2022)Limited reserves of fossil fuels, rising environmental concerns, and a remarkable increase in electricity demand have led to the necessity of harnessing solar energy on a large scale. For this purpose, there has been a ... -
Flow boiling characteristics in a novel minichannel with a step on each corner
(Taylor & Francis Inc, 2020)In the present study, flow boiling in a single minichannel with a longitudinal step on its each corner is studied experimentally. Bubble/flow dynamics, and thus, underlying physical phenomenon is investigated through ... -
Fluid evolution of the Fe-Zn skarn deposits in the Çiftehan (Ulukışla-Niğde) area, south-central Turkey
(Springer, 2023)This study investigated the compositional variations of fluid inclusions in the different stages of mineralization at the Esendemirtepe and Horoz Fe-Zn skarns, south-central Turkey. The skarn zones in the study area consist ... -
Fluid inclusion and stable isotope constraints (C, O, H) on the Dagbasi Fe-Cu-Zn skarn mineralization (Trabzon, NE Turkey)
(Elsevier, 2020)The Dagbasi Fe-Cu-Zn skarn mineralization developed along the contact between the block and lens shaped limestones of the Lower Cretaceous Berdiga Formation and the Upper Cretaceous Dagbasi Granitoid. the exoskam-type ... -
Forecasting wind power generation using artificial neural network
(Munzur Üniersitesi, 2023)Today, among renewable energy sources, wind energy is used effectively as a clean and sustainable energy source in electricity generation. The uncertain nature of renewable energy sources and the smart ability of the ... -
Formability behavior of AH-32 shipbuilding steel strengthened by friction stir process
(Elsevier, 2024)Ships are built by bringing materials into various forms and then joining them. Although materials such as wood, composite materials, polyethylene, and aluminum alloys are used in shipbuilding, it is known that commercial ... -
Free vibration and bending analysis of porous bi-directional FGM sandwich shell using a TSDT p-version finite element method
(Springer, 2024)Compared to the first-order shear deformation theory and other classical shell theories, the higher-order shear theory is deemed more accurate due to its superior ability to capture transverse shear effects, especially ... -
Free vibration and buckling of functionally graded porous beams using analytical, finite element, and artificial neural network methods
(Springer, 2023)In this study, an analytical solution based on the first-order shear deformation theory was performed for free vibration and buckling analysis of functionally graded porous beams (FGM-P) subjected to various boundary ...
