Ara
Toplam kayıt 62, listelenen: 21-30
Experimental study on machinability of pre-hardened Toolox 44 and Nimax mould steels
(Gazi Üniversitesi Mühendislik Mimarlık Fakültesi, 2021)
In this study, the machinability of Nimax and Toolox 44 materials, which are among the mould steels was investigated experimentally. Cutting experiments were carried out with PVD-AlCrN coated carbide end mill using three ...
Düşük dolum oranında ikili karışımlarla yüklü üniform olmayan atımlı ısı borusunun deneysel incelenmesi
(Düzce Üniversitesi, 2021)
Bu çalışmada, düşük bir dolum oranında ikili karışımlarla yüklü, üniform olmayan kanal profiline sahip düz
plakalı kapalı döngülü atımlı bir ısı borusunun ısıl performansı ve akış davranışı deneysel olarak incelenmiştir ...
Impact of tower diameter on power output in solar chimney power plants
(2021)
Güneş bacası güç santralleri düşük bakım maliyetleri ve sıfır CO2 salınımları ile çok cazip güneş enerjisi
sistemleridir. İlk uygulaması olan Manzanares tesisinden sonra geometrik ve iklimsel parametrelerin
sisteme etkisi ...
Kokil kalıba döküm yöntemi ile üretilmiş Al-12Si-(0,02-1)Sr alaşımlarının CVD-TiCN/Al2O3/TiN kaplamalı kesici uç ile tornada işlenmesinde kesme kuvveti ve yüzey pürüzlülüğü üzerine deneysel çalışma
(Gazi Üniversitesi , Fen Bilimleri Enstitüsü, 2022)
In this study, three Al-12Si-Sr alloys containing different ratios (0.02; 0.1 and 1%) strontium (Sr) were
manufactured by the permanent mold casting method. The microstructures of the manufactured alloys were
determined ...
A method to classify steel plate faults based on ensemble learning
(2022)
With the industrial revolution 4.0, machine learning methods are widely used in all
aspects of manufacturing to perform quality prediction, fault diagnosis, or maintenance. In the steel
industry, it is important to ...
The effect of nanofluid usage on electricity consumption in thermoelectric refrigeration application: an experimental study
(2022)
This study investigates the effects of nanofluid use in thermoelectric refrigerators on
electricity consumption. A water-cooled block was placed on the hot surface of the TEC, and
a water-to-air heat ...
The energy efficient configurations of natural convection heat transfer in square enclosures with heatlines
(Yildiz Technical Univ, 2018)
A steady state natural convection heat transfer is numerically investigated in a two-dimensional square enclosure. One of the side walls of the enclosure is brought to high temperature and the upper wall is insulated. the ...
Elyaf takviyeli polimer kompozit malzemelerin farklı delme yöntemleri ile delinmesinde kesme performansının değerlendirilmesi: Literatür Taraması
(2018)
Elyaf takviyeli polimer kompozit (ETPK) malzemeler, yüksek mukavemet ve sönümleme, hafiflik, düşük termal genleşme gibi mühendislik özelliklerinden dolayı uzay ve havacılık sanayisinde cıvatalı, perçinli ve pimli bağlantılarda ...
Experimental study of single-phase fluid flow and heat transfer characteristics in rectangular microchannels
(2018)
In this study, single-phase laminar flow of deionized water through microchannel heat sinks is investigated experimentally. Heat sinks including twenty-nine parallel rectangular channels have been used as the test samples. ...
Stronsiyum ve stronsiyum-magnezyum katkılarının ötektiküstü Al-17Si alaşımının içyapı ve mekanik özelliklerine etkisi
(2019)
Al-17Si, Al-17Si-0,1Sr ve Al-17Si-0,1Sr-0,6Mg alaşımları kokil kalıba döküm yöntemi ile üretilmiştir. Alaşımların yapısal ve mekanik özellikleri üretilen alaşım külçelerinden talaşlı imalat yöntemiyle hazırlanan numuneler ...