Basit öğe kaydını göster

dc.contributor.authorSavaşkan, Temel
dc.contributor.authorHekimoğlu, Ali Paşa
dc.contributor.authorAzaklı, Zeki
dc.contributor.authorÇalış, Merve
dc.date.accessioned2022-11-10T08:25:35Z
dc.date.available2022-11-10T08:25:35Z
dc.date.issued2022en_US
dc.identifier.citationSavaşkan, T., Hekimoğlu, A. P., Azaklı, Z., & Çalış, M. (2022). Effect of Working Conditions on the Lubricated Wear Behavior of Zn-40Al-2Cu-2Si Alloy in the As-Cast and T6 Heat-Treated States. Journal of Tribology-Transactions of the ASME, 144(3), 031702. https://doi.org/10.1115/1.4051264en_US
dc.identifier.issn0742-4787
dc.identifier.issn1528-8897
dc.identifier.urihttps://doi.org/10.1115/1.4051264
dc.identifier.urihttps://hdl.handle.net/11436/6958
dc.description.abstractIn order to determine the effect of working conditions on the lubricated wear behavior of Zn-40Al-2Cu-2Si alloy in the as-cast and T6 heat-treated states, its tribological properties were studied at different oil flowrates, contact pressures, and sliding speeds in comparison with SAE 660 bronze. It was observed that the friction coefficient, temperature, and wear volume of both materials decrease, but their average surface roughness increase with increasing oil flowrate. As the pressure increased, the friction coefficient and average surface roughness of the experimental materials decreased, but their temperature and wear volume increased. It was also found that the working temperature of these materials increased, but their wear volume showed a decrement and a subsequent increment with increasing sliding speed. In addition, their wear volume and average surface roughness showed opposite changes with the sliding speed. Zn-40Al-2Cu-2Si alloy in both as-cast and heat-treated conditions showed lower wear volume and friction coefficient than SAE 660 bronze. This indicates that Zn-40Al-2Cu-2Si alloy can be used to manufacture diesel engine crankshaft journal bearings.en_US
dc.language.isoengen_US
dc.publisherASMEen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectNon-ferrous metals (Zn-40Al-2Cu-2Si alloy)en_US
dc.subjectBearing materialsen_US
dc.subjectWear behavioren_US
dc.subjectSliding frictionen_US
dc.subjectBearingsen_US
dc.subjectHardnessen_US
dc.subjectWear mechanismsen_US
dc.titleEffect of working conditions on the lubricated wear behavior of Zn-40Al-2Cu-2Si alloy in the as-aast and T6 heat-treated statesen_US
dc.typearticleen_US
dc.contributor.departmentRTEÜ, Mühendislik ve Mimarlık Fakültesi, Makine Mühendisliği Bölümüen_US
dc.contributor.institutionauthorHekimoğlu, Ali Paşa
dc.contributor.institutionauthorÇalış, Merve
dc.identifier.doi10.1115/1.4051264en_US
dc.identifier.volume144en_US
dc.identifier.issue3en_US
dc.identifier.startpage031702en_US
dc.relation.journalJournal of Tribology-Transactions of the ASMEen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US


Bu öğenin dosyaları:

DosyalarBoyutBiçimGöster

Bu öğe ile ilişkili dosya yok.

Bu öğe aşağıdaki koleksiyon(lar)da görünmektedir.

Basit öğe kaydını göster