• Türkçe
    • English
  • Türkçe 
    • Türkçe
    • English
  • Giriş
Öğe Göster 
  •   RTEÜ
  • Araştırma Çıktıları | TR-Dizin | WoS | Scopus | PubMed
  • WoS İndeksli Yayınlar Koleksiyonu
  • Öğe Göster
  •   RTEÜ
  • Araştırma Çıktıları | TR-Dizin | WoS | Scopus | PubMed
  • WoS İndeksli Yayınlar Koleksiyonu
  • Öğe Göster
JavaScript is disabled for your browser. Some features of this site may not work without it.

Effect of hybridization and stacking sequence on damage development in AWJ machining of Al/FRP/Al FML composites

Göster/Aç

Tam Metin / Full Text (22.54Mb)

Erişim

info:eu-repo/semantics/closedAccess

Tarih

2024

Yazar

Doğan, Mehmet Akif
Gemi, Lokman
Yazman, Şakir
Ceritbinmez, Ferhat
Yapıcı, Ahmet

Üst veri

Tüm öğe kaydını göster

Künye

Doğan, M. A., Gemi, L., Yazman, Ş., Ceritbinmez, F., & Yapici, A. (2024). Effect of hybridization and stacking sequence on damage development in AWJ machining of Al/FRP/Al FML composites. Journal of Manufacturing Processes, 131, 141–159. https://doi.org/10.1016/j.jmapro.2024.09.017

Özet

In this study, 5 different Al2024/FRP/Al2024 metal stacked composites were produced and their machinability by abrasive water jet machining (AWJM) method was investigated. Synergistic interaction of these materials offers new and improved properties, but machinability remains an area of research due to widely varying mechanical properties. The effects of different stacking and traverse speed on hole quality in cutting with AWJM were determined. The hole diameter deviation (HDD) ratio, kerf, delamination, hole circularity, and surface morphology were analyzed. Result of the current study showed that the increase in traverse speed caused an increase in the HDD ratio, in the visibility of the cutting starting point, in the deviation of circularity, and in the bore-hole damage formation. In all stacks with CFRP, an average deviation of 5 % at the hole entrance and 4 % at the hole exit occurred at a traverse speed of 1000 mm/min. At 400 and 600 mm/min traverse speeds, an average of 2.8 % deviation occurred at the hole entrance and an average of 2.13 % at the hole exit. This proves that the traverse speed has a significant effect on the hole diameter. In addition, as the traverse speed decreased, it was noticed that the layers separated from each other, causing delamination, and therefore the thickness of the FML increased. Different defects were observed to occur in FRP structures used in FML with SEM analysis. Intralayer defects were more dominant in GFRP laminate, whereas interlayer defects were found to form in CFRP laminate.

Kaynak

Journal of Manufacturing Processes

Cilt

131

Bağlantı

https://doi.org/10.1016/j.jmapro.2024.09.017
https://hdl.handle.net/11436/9552

Koleksiyonlar

  • Makine Mühendisliği Bölümü Koleksiyonu [329]
  • WoS İndeksli Yayınlar Koleksiyonu [5260]



DSpace software copyright © 2002-2015  DuraSpace
İletişim | Geri Bildirim
Theme by 
@mire NV
 

 




| Yönerge | Rehber | İletişim |

DSpace@RTEÜ

by OpenAIRE
Gelişmiş Arama

sherpa/romeo

Göz at

Tüm DSpaceBölümler & KoleksiyonlarTarihe GöreYazara GöreBaşlığa GöreKonuya GöreTüre GöreDile GöreBölüme GöreKategoriye GöreYayıncıya GöreErişim ŞekliKurum Yazarına GöreBu KoleksiyonTarihe GöreYazara GöreBaşlığa GöreKonuya GöreTüre GöreDile GöreBölüme GöreKategoriye GöreYayıncıya GöreErişim ŞekliKurum Yazarına Göre

Hesabım

GirişKayıt

İstatistikler

Google Analitik İstatistiklerini Görüntüle

DSpace software copyright © 2002-2015  DuraSpace
İletişim | Geri Bildirim
Theme by 
@mire NV
 

 


|| Rehber|| Yönerge || Kütüphane || Recep Tayyip Erdoğan Üniversitesi || OAI-PMH ||

Recep Tayyip Erdoğan Üniversitesi, Rize, Türkiye
İçerikte herhangi bir hata görürseniz, lütfen bildiriniz:

Creative Commons License
Recep Tayyip Erdoğan Üniversitesi Institutional Repository is licensed under a Creative Commons Attribution-NonCommercial-NoDerivs 4.0 Unported License..

DSpace@RTEÜ:


DSpace 6.2

tarafından İdeal DSpace hizmetleri çerçevesinde özelleştirilerek kurulmuştur.