Başlık için Mühendislik Fakültesi listeleme
Toplam kayıt 847, listelenen: 213-232
-
Effect of gradually expanding flow passages on flow boiling of micro pin fin heat sinks
(Elsevier, 2022)In this paper, effect of gradually expanding flow passages on saturated flow boiling characteristics of micro pin fin heat sinks is experimentally investigated. In this regard, a comparative analysis is performed based on ... -
Effect of grain refinement with titanium on the microstructure, mechanical and corrosion properties of Al-25Zn alloy
(Gazi Univ, Fac Engineering Architecture, 2020)In this study, one binary Al-25n alloys and eleven ternary aluminum-zinc-titanium alloys, Al-25Zn-0.01Ti, Al-25Zn-0.03Ti, Al-25Zn-0.04Ti, Al-25Zn-0.05Ti, Al-25Zn-0.075Ti, Al-25Zn-0.1Ti, Al-25Zn-0.2Ti, Al-25Zn-0.4Ti, ... -
Effect of heat treatment on mechanical and wear properties of Zn-40Al-2Cu-2Si alloy
(Elsevier, 2021)In order to determine the effect of heat treatment on the mechanical and wear properties of Zn-40Al-2Cu-2Si alloy, different heat treatments including homogenization followed by air-cooling (H1), homogenization followed ... -
The effect of heat treatment on the FeCo phase in Tb-Fe-Co thin films
(Elsevier, 2021)Investigation of the magnetic behavior of nanostructured Tb-Fe-Co thin films before and after heat treatment below and above Fe-Co phase crystallization temperature has explored by electron microscopy (SEM), X-ray diffraction ... -
Effect of height to diameter ratio on dynamic characteristics of cemented tailings backfills with fiber reinforcement through impact loading
(Elsevier, 2022)The safety and durability of underground backfilled stopes of metalliferous mines are so crucial owing to several dynamic events such as rock bursting, loads triggered by blasting, and loading conditions under stress. ... -
Effect of hexagonal boron nitride (h-BN) addition on friction behavior of low-steel composite brake pad material for railway applications
(Elsevier, 2021)In this study, low-steel composite friction materials containing different amount of h-BN were developed for railway vehicles. Addition of h-BN has no considerable effect on mechanical properties of the matrix structure. ... -
Effect of hydraulic diameter on flow boiling in rectangular microchannels
(Springer, 2019)An experimental study is conducted to investigate the effect of hydraulic diameter on the saturated flow boiling characteristics of deionized water in parallel rectangular microchannels. Experiments have been performed for ... -
Effect of inlet temperature on flow boiling behavior of expanding micro-pin-fin type heat sinks
(Elsevier, 2023)Heat sinks that cool electronic systems through flow boiling are exposed to working fluids at different inlet temperature. Therefore, in the present study, influence of inlet temperature on boiling performance of a ... -
Effect of isothermal treatment on mechanical and tribological properties of alloy Zn – 40% Al – 2% Cu – 2% Si
(Springer, 2023)The effect of isothermal exposure at temperatures from 100°C to 250°C for 8 hours on the structure, mechanical and tribological properties of the Zn – 40% Al – 2% Cu – 2% Si alloy produced by chill casting is studied. The ... -
Effect of laminar airflow unit diffuser size on pathogen particle distribution in an operating room
(Taylor & Francis Inc, 2020)Operating room ventilation is quite important to protect patients from infection risk inside a surgical field. the laminar flow units (LAF) used in these applications contribute to removal of pathogen particles from the ... -
Effect of layer thickness on the flexural property and microstructure of 3D-printed rhomboid polymer-reinforced cemented tailing composites
(Springer, 2023)For mines with poor ore bodies and surrounding rocks, the general mining method does not allow the ore to be extracted from underground safely and efficiently. For these mines, the downward layered filling mining technique ... -
Effect of magnetic induction intensity and steel fiber rate on strength improvement of cementitious filling composites
(Elsevier, 2024)The underhand cut-fill backfill mining manner (UCFBMM) is widely employed in nonferrous metallic mines, and stability of the artificial backfill top plate directly determines the safety of operators and equipment, which ... -
Effect of mineral admixtures on flow properties of fresh cemented paste backfill: Assessment of time dependency and thixotropy
(Elsevier, 2020)Cemented paste backfill (CPB), an engineered mix consisting typically of tailings, cement and water, has become a regularly used structural material in most mines worldwide. the performance of the CPB structure is dependent ... -
Effect of mineralogical composition of clinoptilolite-bearing tuffs on their performance as a natural pozzolan in cementitious systems
(Techno-Press, 2021)In this study, pozzolanic reactivity and strength activity of zeolitic tuffs containing similar amount of zeolitic phase (clinoptilolite) and different types and amounts of impurities were examined in order to understand ... -
The effect of nanofluid usage on electricity consumption in thermoelectric refrigeration application: an experimental study
(2022)This study investigates the effects of nanofluid use in thermoelectric refrigerators on electricity consumption. A water-cooled block was placed on the hot surface of the TEC, and a water-to-air heat ... -
Effect of Nb doping on structural, electrical and optical properties of spray deposited SnO2 thin films
(Academic Press Ltd- Elsevier Science Ltd, 2013)Nb doped SnO2 transparent conducting thin films were deposited by spray pyrolysis method. Microstructural, morphological, electrical and optical properties of the films were investigated as a function of niobium (Nb) doping, ... -
The effect of occupational choice on job satisfaction and occupational accidents in the construction sector: A case study on Rize and Çorum in Turkey
(Dynamic Academy Yazılım İnşaat San. Tic. Ltd. Şti., 2021)The construction sector is a sector that employs a significant amount of employees in Turkey and appeals to many branches of work and professions. In Turkey, the construction sector ranks first in the statistics ... -
Effect of PCA on nanosized ulexite material prepared by mechanical milling
(Springer Heidelberg, 2017)Raw ulexite (U-3 mm) mineral used as a initial material was milled by using mechanical milling method, the milling time of which is from 0 to 8 h. Particle size, morphology, elemental and crystal structure measurements of ... -
The effect of solid boriding time on the structure, hardness and corrosion properties of AISI 5140 steel
(Maik Nauka/Interperiodica/Springer, 2020)In this study, AISI 5140 steel samples were borided in an electrical furnace at a temperature of 950 degrees C for 4, 6 and 8 h. Structural examinations, hardness measurement and corrosion tests were performed to determine ... -
Effect of strontium additions on the microstructural and mechanical properties of Al-17Si-4Cu-0.6Mg-3Zn (B390+2 wt%Zn) alloy
(Springer, 2022)One Al-17Si-4Cu-0.6Mg-3Zn (B390 + 2 wt%Zn) alloy and five B390 + 2 wt% Zn-Sr alloys were produced by permanent mold casting method. Microstructural evaluations were carried out with microscopic techniques. The phases of ...
