Başlık için Mühendislik Fakültesi listeleme
Toplam kayıt 847, listelenen: 285-304
-
Enhancing mechanical and tribological properties of Ni3Al-15vol%TiC composite by high current pulsed electron beam irradiation
(Elsevier, 2022)Effects of high current pulsed electron beam irradiation (HCPEBI) on the surface microstructure, mechanical properties, room and high temperature tribological behavior of the Ni3Al-15vol%TiC composite were investigated. ... -
Enhancing the power factor of p-type BiSbTe films via deposited with/without Cr seed layer
(Elsevier, 2021)The thermoelectric effect is an efficient method to use waste heat as a primary source of electrical energy. Being a room temperature thermoelectric thin film, p-type BiSbTe is one of the best candidates owing to the ... -
Entail the new path for permanent magnets: Free-standing Hf-Co thin films
(Elsevier Science Sa, 2016)In this work, as an alternative to permanent magnets containing rare earth, we report a method for the preparation of rare-earth-free (REF) free-standing magnetic thin films have been obtained by using a basis sacrificial ... -
Entransy-based environmental and life cycle cost analysis to determine optimum insulation thickness: Effect of the fuel sources
(Gazi Universitesi, 2024)In this study, the influence of fuel sources on entransy-based environmental impact and life cycle cost (LCC) analysis while determining the optimum insulation thickness (OIT) has been investigated. Analyses are carried ... -
Entropy generation of mixed convection in a vertical parallel plate microchannel with asymmetric wall heat flux
(Inderscience Enterprises Ltd, 2015)In this study, the results of a parametric analysis of the entropy generation of mixed convection in a vertical parallel plate microchannel with asymmetric wall heat flux are presented. the fluid flow was assumed as Newtonian ... -
Environmental and sustainability aspects of a recirculating aquaculture system
(Wiley, 2012)This article presents some new exergy-based parameters for Recirculating Aquaculture System (RAS) for Black Sea trout (Salmo trutta labrax) at the Trabzon Central Fisheries Research Institute, Turkey. On the basis of the ... -
Environmental effects of t-shaped groins built on the eastern black sea coast on shore protection
(Parlar Scientific Publications (P S P), 2017)The construction of the double highway on the Black Sea Coast was initiated in 1998, completed in 2000. During the construction, T-shaped groins where were built to protect the shore. in this article, the contribution of ... -
Environmental effects of t-shaped groins built on the eastern black sea coast on shore protection - 2
(Parlar Scientific Publications, 2017)The construction of the double highway on the Black Sea Coast was initiated in 1998, completed in 2000. During the construction, T-shaped groins where were built to protect the shore. In this article, the contribution of ... -
Environmental friendly food smoking technologies
(Springer International Publishing, 2014)This study deals with the development of the food smoking technologies for environmental friendly unit operations. Smoking process include some different unit operations such as salting, drying and smoking. In this regard, ... -
Environmental impact assessment of explosive volcanoes: A case study
(Springer New York, 2013)Although there are some parameters identified in the literature to quantify environmental impact of volcanic eruptions, e.g., Dust Veil Index (DVI), Volcanic Explosivity Index (VEI), and Volcanic Aerosol Index (VAI), no ... -
ESAR: Enhanced secure authentication and revocation scheme for vehicular ad hoc networks
(Elsevier, 2022)Vehicle Ad Hoc Network (VANET) systems that use Public Key Infrastructure (PKI) experience significant delays when checking Certificate Revocation Lists (CRLs) and performing key pair-based asymmetric cryptographic operations. ... -
Estimating the compressive strength of fly ash added concrete using artificial neural networks
(Manisa Celal Bayar Üniversitesi Fen Bilimleri Enstitüsü, 2022)The aim of this study is to develop an artificial intelligence that predicts the compressive strength of fly ash substituted concretes using material mixing ratios. Within the scope of the study, 5 different fly ash mixed ... -
Estimation of the monthly based hourly wind speed characteristics and the generated power characteristics for developing bidding strategies in an actual wind farm: a case study
(Springer Heidelberg, 2013)This manuscript proposes a new approach for the estimation of the monthly based hourly wind speed characteristics and the generated power characteristics in an actual wind farm. the proposed approach uses the probability ... -
Etkin epoklar ile motor hayaline dayalı EEG işaretlerinin sınıflandırma doğruluğunun artırılması
(2018)Beyin bilgisayar arayüzleri (BBA) sadece beyinde üretilen işaretleri kullanarak çeşitli elektronik cihazları kullanmayı olanaklı hale getiren sistemlerdir. Bu sistemlerin yüksek başarımlı olabilmesi için bu işaretlerden ... -
Evaluation of corrosion performance of AZ31 Mg alloy in physiological and highly corrosive solutions
(American Chemical Society, 2023)Resorbable Mg and Mg alloys have gained significant interest as promising biomedical materials. However, corrosion of these alloys can lead to premature reduction in their mechanical properties, and therefore their corrosion ... -
Evaluation of in-duct UV-C lamp array on air disinfection: A numerical analysis
(Taylor & Francis Inc, 2020)In-duct ultraviolet germicidal irradiation systems are effective systems that are used in disinfection of pathogenic particles transported by air that moving through the ventilation systems. Proper design of these systems ... -
Evaluation of structural and optical properties of Mn-Doped ZnO thin films synthesized by Sol-Gel technique
(Springer, 2012)Undoped ZnO and Mn-doped ZnO (MZO) films with 0.25, 0.50, and 0.75 mol pct were synthesized onto glass substrates by sol-gel spin-coating technique, and the effects of Mn on structural, morphologic, and optical properties ... -
Evaluation of the contact problem of functionally graded layer resting on rigid foundation pressed via rigid punch by analytical and numerical (FEM and MLP) methods
(Springer, 2022)In this paper, frictionless contact problem for a functionally graded (FG) layer is considered. The FG layer is subjected to load with a rigid punch and the FG layer is bonded on a rigid foundation. Analysis of this contact ... -
Evaluation of the effect on the permanent tooth germ and the adjacent teeth by finite element impact analysis in the traumatized primary tooth
(Wiley, 2024)Background: One of the primary concerns in the paediatric emergencies is traumatic dental injuries. Objective: This study aimed to create trauma in primary teeth and reveal its effects finite element analysis. Design: ...
