Yayıncı "Springer" Makine Mühendisliği Bölümü Koleksiyonu için listeleme
Toplam kayıt 23, listelenen: 1-20
-
Characteristics of the built environment in the Eastern Mediterranean and Middle East and related energy and climate policies
(Springer, 2024)The Eastern Mediterranean and Middle East (EMME) region hosts some of the world's most influential and troubled cities. It is also a hotspot of climate change and socio-economic and political turbulence, which inflate the ... -
The combined effects of filling ratio and inclination angle on thermal performance of a closed loop pulsating heat pipe
(Springer, 2021)In the present study, a series of experiments are conducted to investigate the thermal performance of a copper made pulsating heat pipe consisting of uniform flow passages with the cross section of 2 mm x 2 mm. Test ... -
Conical coaxial impinging air jets: angle effect on the heat transfer performance
(Springer, 2020)Herein, an experimental attempt is conducted to research thermal and flow behaviors of an impinging jet exiting from a coaxial type nozzle with a conical outer and a circular inner outlets. the experiments include four ... -
Effect of boronizing on operating stability of steel AISI 304L under erosion impact of hard particles
(Springer, 2021)The effect of solid boronizing at 950 degrees C for 2 and 4 h on the phase composition, microstructure, hardness and abrasive wear of steel AISI 304L is studied under the impact of a flow of hard particles. The boronized ... -
Effect of hydraulic diameter on flow boiling in rectangular microchannels
(Springer, 2019)An experimental study is conducted to investigate the effect of hydraulic diameter on the saturated flow boiling characteristics of deionized water in parallel rectangular microchannels. Experiments have been performed for ... -
Effect of isothermal treatment on mechanical and tribological properties of alloy Zn – 40% Al – 2% Cu – 2% Si
(Springer, 2023)The effect of isothermal exposure at temperatures from 100°C to 250°C for 8 hours on the structure, mechanical and tribological properties of the Zn – 40% Al – 2% Cu – 2% Si alloy produced by chill casting is studied. The ... -
Effect of strontium additions on the microstructural and mechanical properties of Al-17Si-4Cu-0.6Mg-3Zn (B390+2 wt%Zn) alloy
(Springer, 2022)One Al-17Si-4Cu-0.6Mg-3Zn (B390 + 2 wt%Zn) alloy and five B390 + 2 wt% Zn-Sr alloys were produced by permanent mold casting method. Microstructural evaluations were carried out with microscopic techniques. The phases of ... -
Effect of strontium on the microstructure, mechanical, and tribological properties of the Zn-40Al-2Cu alloy
(Springer, 2023)Zn-40Al-2Cu and Zn-40Al-2Cu-0.1Sr alloys were produced by permanent mold casting method. The microstructure, mechanical properties and wear resistance of the produced alloys were investigated. Microstructural examinations ... -
The effect of Total flowrate on the cooling performance of swirling coaxial impinging jets
(Springer, 2019)Thermal management ability of swirling coaxial confined impinging air jets (SCCIAJ) are experimentally studied for different total flowrate. the coaxial structure of the jet is provided by a nozzle which is a cylindrical ... -
Experimental and theoretical examination of the energy performance and CO2 emissions of room air conditioners utilizing natural refrigerant R290 as a substitute for R22
(Springer, 2023)The purpose of this research is to analyze the performance of an air conditioner that uses natural refrigerant R290 both analytically and experimentally. The feasibility of R290 for R22 air conditioner is examined thoroughly. ... -
Experimental investigation and a new predictive tool for thermal performance of pulsating heat pipes
(Springer, 2023)In the present study, binary-fluid-charged uniform and nonuniform flat plate closed loop pulsating heat pipes (FP-CLPHP) are experimentally investigated in comparative manner, and a novel correlation with innovative point ... -
An experimental study on microstructural, mechanical and machinability properties of as-cast and heat-treated al-7Si-mg alloy
(Springer, 2024)The automotive industry is constantly striving for targets for the development of lightweight materials for less fuel consumption and carbon emissions. For this purpose, lighter and higher-performance Al-Si alloys with ... -
Investigation of the effects of miscible and immiscible binary fluids on thermal performance of pulsating heat pipes
(Springer, 2021)Present paper reports and discusses experimental results related to thermal and flow characteristics of asymmetrical designed flat plate closed loop pulsating heat pipe charged with miscible and immiscible binary fluids. ... -
Machine learning models to estimate the elastic modulus of weathered magmatic rocks
(Springer, 2021)In recent years, several soft computing models have been proposed to estimate the elastic modulus of magmatic rocks. However, there are lacks in models that consider the different weathering degrees in determining the ... -
Mechanical properties of Al-9Si-0.6Mg-0.1Sr alloy processed by successive hot and cold multi-directional forging
(Springer, 2023)In this study, the effect of successive hot and cold multi-directional forging (MDF) on the mechanical properties of the Al-9Si-0.6Mg-0.1Sr alloy was explored. The alloy was first homogenized and then forged at 200°C from ... -
The numerical evaluation of crash performance of the pressurized thin-walled tubes
(Springer, 2022)This paper aims to investigate the energy absorption characteristics of the pressurized thin-walled tubes under axial impact by numerical simulations. The Arbitrary Lagrangian-Eulerian (ALE) model with the Fluid-Structure ... -
On the tse of nanofluids in solar energy applications
(Springer, 2020)Renewable energy technologies are in the centre of interest to narrow the gap between fossil fuels and clean energy systems. the dominant role of solar energy systems among the alternatives is beyond question owing to being ... -
Optimizing soybean biofuel blends for sustainable urban medium-duty commercial vehicles in India: an AI-driven approach
(Springer, 2024)This article presents the outcomes of a research study focused on optimizing the performance of soybean biofuel blends derived from soybean seeds specifically for urban medium-duty commercial vehicles. The study took into ... -
Performance evaluation of using evacuated tubes solar collector, perforated fins, and pebbles in a solar still - experimental study and CO2 mitigation analysis
(Springer, 2022)The combination of various methods of increasing evaporation rate can highly impact the performance of solar desalination. This investigation aims to find the impact of using evacuated tubes solar collector, perforated ... -
Prospects and challenges of renewable energy-based microgrid system in Bangladesh: a comprehensive review
(Springer, 2022)Global energy demand is continuously increasing where the pollution and harmful greenhouse gases that originated from the burning of fossil fuels are alarming. Various policies, targets, and strategies are being set to the ...