Yayıncı "Taylor & Francis Inc" Makine Mühendisliği Bölümü Koleksiyonu için listeleme
Toplam kayıt 14, listelenen: 1-14
-
Effect of laminar airflow unit diffuser size on pathogen particle distribution in an operating room
(Taylor & Francis Inc, 2020)Operating room ventilation is quite important to protect patients from infection risk inside a surgical field. the laminar flow units (LAF) used in these applications contribute to removal of pathogen particles from the ... -
Effects of contact pressure and sliding speed on the unlubricated friction and wear properties of Zn-15Al-3Cu-1Si alloy
(Taylor & Francis Inc, 2016)The unlubricated friction and wear properties of Zn-15Al-3Cu-1Si alloy were studied over a range of contact pressure (1-5 MPa) and sliding speed (0.5-2.5 ms(-1)) for a sliding distance of 2,500m using a block-on-disc type ... -
Evaluation of in-duct UV-C lamp array on air disinfection: A numerical analysis
(Taylor & Francis Inc, 2020)In-duct ultraviolet germicidal irradiation systems are effective systems that are used in disinfection of pathogenic particles transported by air that moving through the ventilation systems. Proper design of these systems ... -
Exergetic sustainability indicators as a tool in commercial aircraft: a case study for a turbofan engine
(Taylor & Francis Inc, 2015)This paper focuses on the exergetic sustainability indicators of a medium-range commercial aircraft engine for constant reference environment and ground running conditions. First, a detailed exergy analysis of turbofan ... -
Flow boiling characteristics in a novel minichannel with a step on each corner
(Taylor & Francis Inc, 2020)In the present study, flow boiling in a single minichannel with a longitudinal step on its each corner is studied experimentally. Bubble/flow dynamics, and thus, underlying physical phenomenon is investigated through ... -
Influence of ventilation strategies on dispersion and removal of fine particles: An experimental and simulation study
(Taylor & Francis Inc, 2020)In this study, effect of inlet/outlet configurations on the dispersion and removal of fine particles are examined experimentally and numerically. Ten different inlet/outlet configurations are tested for three different ... -
The mechanical compression performance of ultra-fine grained stainless steel pyramidal lattice core
(Taylor & Francis Inc, 2019)Severe plastic deformation (SPD) techniques are prospective ones having ability for desirable high mechanical properties to be achieved without any chemical change in metals. Equal-channel angular pressing (ECAP), one of ... -
Particle dispersion and deposition in displacement ventilation systems combined with floor heating
(Taylor & Francis Inc, 2020)The aim of this study is to investigate dispersion and deposition characteristics of different particle diameters (0.5-5-10 mu m) for a displacement ventilated and floor heated environment, experimentally and numerically. ... -
Prediction of pressure drop for flow boiling in rectangular multi-microchannel heat sinks
(Taylor & Francis Inc, 2019)In this study, two new correlations are developed to predict pressure drop for the flow boiling in micro systems with low mass flux. the correlations developed rely on extensive experimental results. Experiments are conducted ... -
Prediction of two-phase heat transfer coefficient of flow boiling in minichannels
(Taylor & Francis Inc, 2020)The present study mainly concentrates on the prediction of two-phase heat transfer coefficient for saturated flow boiling conditions in minichannels. the experimental database has been generated through systematic experiments ... -
Processing of T6 heat-treated Al-12Si-0.6Mg alloy
(Taylor & Francis Inc, 2020)In this study, ternary Al-12Si-0.6Mg material was manufactured by gravity die casting method in induction melting furnace. Microstructure images of alloy were taken on optical microscope after T6 heat treatment. Hardness, ... -
A review on thin-layer drying-curve equations
(Taylor & Francis Inc, 2014)This paper presents a comprehensive review of thin-layer drying-curve models available in the literature and their comparisons for single-layer drying applications from 2003 to 2013. in this regard, a total of 67 models ... -
Saturated flow boiling characteristics in single rectangular minichannels: effect of aspect ratio
(Taylor & Francis Inc, 2018)In this study, saturated flow boiling characteristics of deionized water in single rectangular minichannels are investigated experimentally. A special attention is paid to the effect of aspect ratio (channel width to depth, ...