Başlık için Mühendislik Fakültesi listeleme
Toplam kayıt 847, listelenen: 197-216
-
Effect of air pressure on nanofiber production in solution blowing method
(Gazi Univ, Fac Engineering Architecture, 2020)In this study, effect of air pressure on nanofiber diameter and morphology was studied for solution blowing technique. A computational fluid dynamics (CFD) analysis was realized via ANSYS (R) Fluent software, and the results ... -
Effect of aluminosilicate precursors and curing regime on physico-mechanical durability and microstructural characteristics of coral geopolymers (Cor-Geo): Cleaner production for coral islands
(Elsevier, 2023)This study investigated the mechanical, durability, microstructure, carbon footprint and cost characteristics of new-generation metakaolin-based geopolymer composites. Instead of GBFS, 25 % metakaolin was used, and 25 ... -
Effect of annealing temperature on K-shell X-ray fluorescence parameters of zinc oxide thin films prepared by the sol-gel method
(Taylor & Francis Inc, 2019)Zinc oxide thin films were grown on a glass substrate by a sol-gel process using a spin-coating technique. the obtained thin films were annealed between 350 degrees C and 550 degrees C in 50 degrees C steps and were then ... -
Effect of arc re-melting on microstructure, mechanical and tribological properties of commercial 390A alloy
(Elsevier, 2021)To investigate the effect of the arc re-melting on the microstructure, mechanical and tribological properties of the 390A alloy, its ingot produced by the conventional induction melting method was subjected to the arc ... -
Effect of boronizing on operating stability of steel AISI 304L under erosion impact of hard particles
(Springer, 2021)The effect of solid boronizing at 950 degrees C for 2 and 4 h on the phase composition, microstructure, hardness and abrasive wear of steel AISI 304L is studied under the impact of a flow of hard particles. The boronized ... -
The effect of capillarity on chloride transport and the prediction of the accumulation region of chloride in concretes with reinforcement corrosion
(Elsevier, 2012)In this study, 20-year-old residential buildings which have reinforcement bar corrosion in their basement columns were investigated in Rize, Turkey. The reason for the occurrence of high steel corrosion in only some certain ... -
Effect of case depths on corrosion properties of hard anodic oxidized A356 aluminum alloy
(World Stientific Publishing, 2023)In this work, A356 alloy samples having a dimension of 4x20x20mm were coated by hard anodic oxidation method at eight different thicknesses up to similar to 80 mu m. The sample surfaces and longitudinal section of these ... -
Effect of characteristics of natural zeolites on their geopolymerization
(Elsevier, 2021)The properties of clinoptilolite-based geopolymers are investigated with a focus on the parameters affecting the reactivity of clinoptilolite in a geopolymer binder. A complete characterization of raw materials was carried ... -
Effect of content and length of polypropylene fibers on strength and microstructure of cementitious tailings-waste rock fill
(MDPI, 2023)The mechanical strength properties of cemented tailings backfill are very important for the safe and environmentally friendly mining of mineral resources. To check the impact of polypropylene fiber on strength and ... -
Effect of content of defluorinated solid waste on macroscopic strength and microstructural evolution of cemented tail filling composites
(Elsevier, 2024)Solid waste created by the ferrous mining industry has a major number of notable differences. The deficiency of recognition of solid waste features is the key factor limiting its discarding and reuse. In this paper, cemented ... -
The effect of daylight saving time options on electricity consumption of Turkey
(Elsevier Ltd, 2010)Most of the developed countries in the world use Daylight Saving Time (DST) as an energy conservation method. This study focuses on the effects of DST on electrical lighting in the buildings in Turkey. Turkey might adjust ... -
Effect of different abutment materials on stress distribution in peripheral bone and dental implant system
(Yildiz Technical Univ, 2020)In this study, the effect of different abutment materials on the stress distribution in bone tissue around the dental implant was investigated using ANSYS packet program based on finite element method. the study aims to ... -
Effect of different zinc contents on the structural, mechanical and tribological properties of EN AC-48100 (Al-17Si-4Cu-Mg) Alloy
(Gazi Univ, Fac Engineering Architecture, 2020)In this study, Al-17Si-4Cu-0.6Mg-0.2Ti which is based of the EN AC-48100 alloy, Al-17Si-4Cu-0.6Mg0.2Ti-1Zn, Al-17Si-4Cu-0.6Mg-0.2Ti-2Zn, Al- 17Si-4Cu-0.6Mg-0.2Ti-3Zn, Al-17Si-4Cu-0.6Mg-0.2Ti-4Zn and Al-17Si-4Cu-0.6Mg-0.2Ti-5Zn ... -
Effect of double cross sectional ratio on performance characteristics of pulsating heat pipes
(Elsevier, 2021)Effect of double cross sectional ratio on performance characteristics of pulsating heat pipes is experimentally investigated. The cross sectional ratios in the evaporator and condenser sides are different from each other, ... -
Effect of fin width ratio on thermal performance of fin based-heat sink with phase change materials
(Elsevier, 2023)The rapid development of electronics, coupled with need of miniaturization in the design and manufacture, makes heat dissipation, which is critical for the performance, lifetime, and reliability of the components extremely ... -
The effect of fluorine and tungsten co-doping on optical, electrical and structural properties of tin(IV) oxide thin films prepared by sol-gel spin coating method
(Technical Univ Wroclaw, 2013)Fluorine and tungsten co-doped tin(IV) oxide (WFTO) thin films have been prepared first time by a sol gel spin coating method. the effect of F and W co-dopant ratio on optical, electrical and structural properties of SnO2 ... -
Effect of gradually expanding flow passages on flow boiling of micro pin fin heat sinks
(Elsevier, 2022)In this paper, effect of gradually expanding flow passages on saturated flow boiling characteristics of micro pin fin heat sinks is experimentally investigated. In this regard, a comparative analysis is performed based on ... -
Effect of grain refinement with titanium on the microstructure, mechanical and corrosion properties of Al-25Zn alloy
(Gazi Univ, Fac Engineering Architecture, 2020)In this study, one binary Al-25n alloys and eleven ternary aluminum-zinc-titanium alloys, Al-25Zn-0.01Ti, Al-25Zn-0.03Ti, Al-25Zn-0.04Ti, Al-25Zn-0.05Ti, Al-25Zn-0.075Ti, Al-25Zn-0.1Ti, Al-25Zn-0.2Ti, Al-25Zn-0.4Ti, ... -
Effect of heat treatment on mechanical and wear properties of Zn-40Al-2Cu-2Si alloy
(Elsevier, 2021)In order to determine the effect of heat treatment on the mechanical and wear properties of Zn-40Al-2Cu-2Si alloy, different heat treatments including homogenization followed by air-cooling (H1), homogenization followed ... -
The effect of heat treatment on the FeCo phase in Tb-Fe-Co thin films
(Elsevier, 2021)Investigation of the magnetic behavior of nanostructured Tb-Fe-Co thin films before and after heat treatment below and above Fe-Co phase crystallization temperature has explored by electron microscopy (SEM), X-ray diffraction ...
