Başlık için Mühendislik Fakültesi listeleme
Toplam kayıt 847, listelenen: 204-223
-
Effect of characteristics of natural zeolites on their geopolymerization
(Elsevier, 2021)The properties of clinoptilolite-based geopolymers are investigated with a focus on the parameters affecting the reactivity of clinoptilolite in a geopolymer binder. A complete characterization of raw materials was carried ... -
Effect of content and length of polypropylene fibers on strength and microstructure of cementitious tailings-waste rock fill
(MDPI, 2023)The mechanical strength properties of cemented tailings backfill are very important for the safe and environmentally friendly mining of mineral resources. To check the impact of polypropylene fiber on strength and ... -
Effect of content of defluorinated solid waste on macroscopic strength and microstructural evolution of cemented tail filling composites
(Elsevier, 2024)Solid waste created by the ferrous mining industry has a major number of notable differences. The deficiency of recognition of solid waste features is the key factor limiting its discarding and reuse. In this paper, cemented ... -
The effect of daylight saving time options on electricity consumption of Turkey
(Elsevier Ltd, 2010)Most of the developed countries in the world use Daylight Saving Time (DST) as an energy conservation method. This study focuses on the effects of DST on electrical lighting in the buildings in Turkey. Turkey might adjust ... -
Effect of different abutment materials on stress distribution in peripheral bone and dental implant system
(Yildiz Technical Univ, 2020)In this study, the effect of different abutment materials on the stress distribution in bone tissue around the dental implant was investigated using ANSYS packet program based on finite element method. the study aims to ... -
Effect of different zinc contents on the structural, mechanical and tribological properties of EN AC-48100 (Al-17Si-4Cu-Mg) Alloy
(Gazi Univ, Fac Engineering Architecture, 2020)In this study, Al-17Si-4Cu-0.6Mg-0.2Ti which is based of the EN AC-48100 alloy, Al-17Si-4Cu-0.6Mg0.2Ti-1Zn, Al-17Si-4Cu-0.6Mg-0.2Ti-2Zn, Al- 17Si-4Cu-0.6Mg-0.2Ti-3Zn, Al-17Si-4Cu-0.6Mg-0.2Ti-4Zn and Al-17Si-4Cu-0.6Mg-0.2Ti-5Zn ... -
Effect of double cross sectional ratio on performance characteristics of pulsating heat pipes
(Elsevier, 2021)Effect of double cross sectional ratio on performance characteristics of pulsating heat pipes is experimentally investigated. The cross sectional ratios in the evaporator and condenser sides are different from each other, ... -
Effect of fin width ratio on thermal performance of fin based-heat sink with phase change materials
(Elsevier, 2023)The rapid development of electronics, coupled with need of miniaturization in the design and manufacture, makes heat dissipation, which is critical for the performance, lifetime, and reliability of the components extremely ... -
The effect of fluorine and tungsten co-doping on optical, electrical and structural properties of tin(IV) oxide thin films prepared by sol-gel spin coating method
(Technical Univ Wroclaw, 2013)Fluorine and tungsten co-doped tin(IV) oxide (WFTO) thin films have been prepared first time by a sol gel spin coating method. the effect of F and W co-dopant ratio on optical, electrical and structural properties of SnO2 ... -
Effect of gradually expanding flow passages on flow boiling of micro pin fin heat sinks
(Elsevier, 2022)In this paper, effect of gradually expanding flow passages on saturated flow boiling characteristics of micro pin fin heat sinks is experimentally investigated. In this regard, a comparative analysis is performed based on ... -
Effect of grain refinement with titanium on the microstructure, mechanical and corrosion properties of Al-25Zn alloy
(Gazi Univ, Fac Engineering Architecture, 2020)In this study, one binary Al-25n alloys and eleven ternary aluminum-zinc-titanium alloys, Al-25Zn-0.01Ti, Al-25Zn-0.03Ti, Al-25Zn-0.04Ti, Al-25Zn-0.05Ti, Al-25Zn-0.075Ti, Al-25Zn-0.1Ti, Al-25Zn-0.2Ti, Al-25Zn-0.4Ti, ... -
Effect of heat treatment on mechanical and wear properties of Zn-40Al-2Cu-2Si alloy
(Elsevier, 2021)In order to determine the effect of heat treatment on the mechanical and wear properties of Zn-40Al-2Cu-2Si alloy, different heat treatments including homogenization followed by air-cooling (H1), homogenization followed ... -
The effect of heat treatment on the FeCo phase in Tb-Fe-Co thin films
(Elsevier, 2021)Investigation of the magnetic behavior of nanostructured Tb-Fe-Co thin films before and after heat treatment below and above Fe-Co phase crystallization temperature has explored by electron microscopy (SEM), X-ray diffraction ... -
Effect of height to diameter ratio on dynamic characteristics of cemented tailings backfills with fiber reinforcement through impact loading
(Elsevier, 2022)The safety and durability of underground backfilled stopes of metalliferous mines are so crucial owing to several dynamic events such as rock bursting, loads triggered by blasting, and loading conditions under stress. ... -
Effect of hexagonal boron nitride (h-BN) addition on friction behavior of low-steel composite brake pad material for railway applications
(Elsevier, 2021)In this study, low-steel composite friction materials containing different amount of h-BN were developed for railway vehicles. Addition of h-BN has no considerable effect on mechanical properties of the matrix structure. ... -
Effect of hydraulic diameter on flow boiling in rectangular microchannels
(Springer, 2019)An experimental study is conducted to investigate the effect of hydraulic diameter on the saturated flow boiling characteristics of deionized water in parallel rectangular microchannels. Experiments have been performed for ... -
Effect of inlet temperature on flow boiling behavior of expanding micro-pin-fin type heat sinks
(Elsevier, 2023)Heat sinks that cool electronic systems through flow boiling are exposed to working fluids at different inlet temperature. Therefore, in the present study, influence of inlet temperature on boiling performance of a ... -
Effect of isothermal treatment on mechanical and tribological properties of alloy Zn – 40% Al – 2% Cu – 2% Si
(Springer, 2023)The effect of isothermal exposure at temperatures from 100°C to 250°C for 8 hours on the structure, mechanical and tribological properties of the Zn – 40% Al – 2% Cu – 2% Si alloy produced by chill casting is studied. The ... -
Effect of laminar airflow unit diffuser size on pathogen particle distribution in an operating room
(Taylor & Francis Inc, 2020)Operating room ventilation is quite important to protect patients from infection risk inside a surgical field. the laminar flow units (LAF) used in these applications contribute to removal of pathogen particles from the ... -
Effect of layer thickness on the flexural property and microstructure of 3D-printed rhomboid polymer-reinforced cemented tailing composites
(Springer, 2023)For mines with poor ore bodies and surrounding rocks, the general mining method does not allow the ore to be extracted from underground safely and efficiently. For these mines, the downward layered filling mining technique ...
